Jog 50 LC Project

markybda · 03-09-2008, 04:39

I have a Jog 50 LC. 2004
I just have a few ?'s....

does anyone have diagrams for the minerlli (However u spell it

) LC motor?

i am having issues with getting my clutch working and would like to see the various washer/spacer settings...

i currently have a polini bell, 2 pad clutch, and complete torque driver set along with a maloissi red spring.
When i change out the torque driver to my maliossi i cannot get the clutch to disengage. I am running 2 really thin flat washers between the bell and the center of the tubing comming out of the polini torques....

when i spin the bell with the maloissi 1 it engages.... polini setup... fine... guidance?
thanks,
MarkyBDA

**$aint** · 09-09-2008, 19:15

You'll probably need a thicker spacer/washer.

For a diagram, see this page on the wiki
http://wiki.scooterforum.net/index.php/Overrange

I usually need both the spacer and the shim for the clutch bell to rotate freely.

markybda · 14-09-2008, 00:52

Thanks!!
i NEED TO GET THE SPACER....

Now i have another problem....
my bike is sparking on the frame where the small springs are on the frame ... kinda mini suspension...
anyone encountered this before on a minerilli?

markybda · 29-09-2008, 04:41

Quote:

Originally Posted by markybda

Thanks!!
i NEED TO GET THE SPACER....

Now i have another problem....
my bike is sparking on the frame where the small springs are on the frame ... kinda mini suspension...
anyone encountered this before on a minerilli?

I ran a new ground from the chasis to the motor and this fixed the sparking problem.

Put on a new NGK jet ski plug cap, and put the bike back together.
The bike runs fine, just the tail light soed not work, only the brake light comes on when I hit the rear brakes, nothing from the front brakes...
Also, when I hold in the rear brake while turning the key off, the bike does not turn off till I let go of the rear brake!!!>|?!?!
anyone ever heard of this?

If i disconnect the brown wire for the solenoid of the starter, the bike instanty tunrs off when I turn the key off.

Ideas?
Marky

tiba_karotsu · 01-10-2008, 06:04

you may have a wiring problem there, trace it & fix it.

03-09-2008, 04:39	#1 (permalink)
markybda Team Insanity Racing	Jog 50 LC Project I have a Jog 50 LC. 2004 I just have a few ?'s.... does anyone have diagrams for the minerlli (However u spell it ) LC motor? i am having issues with getting my clutch working and would like to see the various washer/spacer settings... i currently have a polini bell, 2 pad clutch, and complete torque driver set along with a maloissi red spring. When i change out the torque driver to my maliossi i cannot get the clutch to disengage. I am running 2 really thin flat washers between the bell and the center of the tubing comming out of the polini torques.... when i spin the bell with the maloissi 1 it engages.... polini setup... fine... guidance? thanks, MarkyBDA Last edited by markybda; 03-09-2008 at 04:53. Reason: being specific

09-09-2008, 19:15	#2 (permalink)
$aint holy scootertuning	You'll probably need a thicker spacer/washer. For a diagram, see this page on the wiki http://wiki.scooterforum.net/index.php/Overrange I usually need both the spacer and the shim for the clutch bell to rotate freely. __________________ Goed hardrijden is een dure hobby...

01-10-2008, 06:04	#5 (permalink)
tiba_karotsu OVERREV TUNING	you may have a wiring problem there, trace it & fix it. __________________ 2stroke tuning the Dutch way + infusion with Filipino ingenuity = OveRReV TuNinG Rev Higher, Go Faster, Race Harder, My Desire

14-09-2008, 00:52	#3 (permalink)
markybda Team Insanity Racing	Thanks!! i NEED TO GET THE SPACER.... Now i have another problem.... my bike is sparking on the frame where the small springs are on the frame ... kinda mini suspension... anyone encountered this before on a minerilli?